Prof. Dr. László Juhász

  • Modelling, parameter identification, and simulation of mechatronics systems
  • Control of mechatronics systems
  • Model-based control design and testing
  • Model-based control design for FPGA-based controller
  • Mathematics

Professor

C 218

0991/3615-532

0991/3615-297


Beitrag (Sammelband oder Tagungsband)
  • Alireza Tajafari Sahebi
  • Amir Samiee
  • László Juhász
MRAC Implementation for Electric Throttle Valve, pg. 6-12.
  • 2020

DOI: 10.1109/ACIT49673.2020.9208929

Design, implementation and testing of a model reference adaptive controller for an electric throttle valve are presented. An important step by design an adaptive controller is to find an adaptation mechanism. For this purpose, we employed the Lyapunov stability theory. The main challenge in this project originates from a certain term in the updating rules. This term contains the angular velocity, which is not measurable directly. Numerical differentiation of the measured angular position yields a noisy signal. To overcome this problem, we used a non-ideal derivative method. The use of a non-linear state observer based on extended Kalman filter could significantly enhance the control quality. This task is currently in progress.
  • Elektrotechnik und Medientechnik
  • TSZ Weißenburg
  • DIGITAL
Beitrag (Sammelband oder Tagungsband)
  • László Juhász
  • Amir Samiee
  • W. Engelbrecht
XCP Service Integration for Model-Based, Automatic Production Code Generation, pg. 1-6.
  • 2019

DOI: 10.1109/EUROCON.2019.8861774

Automated, model-based production code generation is widely used in the development and testing of electronic control units (ECUs). During ECU commissioning, extensive tests of the implemented control algorithms are required. Knowledge of the internal values and states of the ECU software are essential for verifying the correct software functionality by means of complex control algorithms. Calibration and measurement services make it possible to observe the ECU-internal memory values associated with the variables originating from the function model. Furthermore, the final adjustment of control parameters in the production ECU can be performed by means of calibration services. For these reasons, calibration and measurement through service integration is widely applied in both the automotive industry and other industrial fields. Integrating measurement and calibration services is therefore an important task for engineers working with model-based control development and, particularly, ECU production code integration. This paper describes an example integration of the Universal Measurement and Calibration Protocol (XCP) for model-based automatic code generation. The application used for the service integration is the commercially available Motor Control Education Kit (MEDKit) from Emerge-Engineering and dSPACE GmbH. The model-based automatic code generation is performed using the production code generator dSPACE TargetLink. The integration of the XCP on CAN protocol is completed in the scope of student projects. The upgraded MEDKit demonstrator will be used for education purposes in the Deggendorf Institute of Technology.
  • TSZ Weißenburg
  • Elektrotechnik und Medientechnik
  • DIGITAL
Patent
  • László Juhász
  • J. Lakemeier
Method for configuring a tester equipped for testing a control unit
  • 2019
  • Angewandte Informatik
  • DIGITAL
Vortrag
  • László Juhász
  • J. Sahu
  • Amir Samiee
  • Nicolas Tiefnig
  • Michael Wagner
Model-Driven Engineering in Education: Position Control of an Electronic Throttle Valve

In: 5th EcETRAN International Conference for Electronics, Telecommunications, Computers, Automatic Control and Nuclear Engineering

  • 2018
  • Elektrotechnik und Medientechnik
  • TSZ Weißenburg
  • MOBIL
Zeitschriftenartikel
  • I. Juhász Junger
  • D. Wehlage
  • R. Döttjer
  • T. Grothe
  • László Juhász
  • C. Grassmann
  • T. Blachowicz
  • A. Ehrmann
Dye-Sensitized Solar Cells with Electrospun Nanofiber Mat-Based Counter Electrodes, vol. 11, pg. 1604.

In: Materials

  • 2018

DOI: 10.3390/ma11091604

Textile-based dye-sensitized solar cells (DSSCs) can be created by building the necessary layers on a textile fabric or around fibers which are afterwards used to prepare a textile layer, typically by weaving. Another approach is using electrospun nanofiber mats as one or more layers. In this work, electrospun polyacrylonitrile (PAN) nanofiber mats coated by a conductive polymer poly(3,4-ethylenedioxythiopene) polystyrene sulfonate (PEDOT:PSS) were used to produce the counter electrodes for half-textile DSSCs. The obtained efficiencies were comparable with the efficiencies of pure glass-based DSSCs and significantly higher than the efficiencies of DSSCs with cotton based counter electrodes. The efficiency could be further increased by increasing the number of PEDOT:PSS layers on the counter electrode. Additionally, the effect of the post treatment of the conductive layers by HCl, acetic acid, or dimethyl sulfoxide (DMSO) on the DSSC efficiencies was investigated. Only the treatment by HCl resulted in a slight improvement of the energy-conversion efficiency.
  • Elektrotechnik und Medientechnik
  • NACHHALTIG
Beitrag (Sammelband oder Tagungsband)
  • Amir Samiee
  • J. Sahu
  • Nicolas Tiefnig
  • Michael Wagner
  • A. Baumgartner
  • László Juhász
Model-Driven Engineering in Education, pg. 9-14.
  • 2018
  • TSZ Weißenburg
  • Elektrotechnik und Medientechnik
  • DIGITAL
Vortrag
  • Amir Samiee
  • J. Sahu
  • Nicolas Tiefnig
  • Michael Wagner
  • A. Baumgartner
  • László Juhász
Model-Driven Engineering in Education

In: 18th International Conference on Mechatronics-Mechatronika 2018

  • 2018
  • TSZ Weißenburg
  • Elektrotechnik und Medientechnik
  • DIGITAL
Zeitschriftenartikel
  • László Juhász
  • I. Juhász Junger
Spectral Analysis and Parameter Identification of Textile-Based Dye-Sensitized Solar Cells, vol. 11, pg. 1623.

In: Materials

  • 2018

DOI: 10.3390/ma11091623

  • Elektrotechnik und Medientechnik
  • NACHHALTIG
Patent
  • László Juhász
Verfahren zur Konfiguration eines für das Testen eines Steuergeräts eingerichteten Testgeräts
  • 2016
  • Elektrotechnik und Medientechnik
  • DIGITAL
Patent
  • László Juhász
Computerimplementiertes Verfahren zur Berechnung und Ausgabe von Steuerimpulsen durch eine Steuereinheit
  • 2015
  • Elektrotechnik und Medientechnik
  • DIGITAL
Beitrag (Sammelband oder Tagungsband)
  • F. Schütte
  • László Juhász
  • A. Tenge
Integration of EtherCAT in Advanced Test Systems - Solutions and Challenges
  • 2013
  • Extern
Zeitschriftenartikel
  • László Juhász
  • J. Maas
Control of Hybrid Nanopositioning Systems for Trajectory-Tracking Applications, vol. 23, pg. 617-629.

In: Mechatronics

  • 2013

DOI: 10.1016/j.mechatronics.2013.06.008

In many industrial applications positioning systems are required to follow trajectory paths in the range of several centimeters and featuring at the same time a nanometre-range precision. Neither pure piezoelectric stages nor standard positioning systems with motor and spindle are able to meet such requirements as a single actuator, because of the small operation range on the one hand and inadequacies like backlash and friction on the other hand. Hybrid positioning systems, realized as a combination of a “coarse” and a “fine” actuator, aim to solve this problem. The wide range of applications enables a considerable market potential for such devices, but yields changing control requirements due to the high variety of possible positioned objects and positioning tasks and requires therefore a high-performance control system. In this paper a model-based control design for piezoelectric hybrid nanopositioning systems is presented. The proposed control consists of a multivariable state-feedback control on the basis of a novel plant representation offering a sufficient robustness. The designed control is realized and experimentally tested with a commercially available hybrid nanopositioning system featuring a DC drive, representing the coarse actuator, and a piezoelectric actuator utilized as fine actuator.
  • Elektrotechnik und Medientechnik
Beitrag (Sammelband oder Tagungsband)
  • J. Maas
  • László Juhász
Adaptive Regelung für piezoelektrisch-basierte Hybridsysteme, pg. 93-101.
  • 2011
  • Elektrotechnik und Medientechnik
Zeitschriftenartikel
  • László Juhász
  • J. Maas
FPGA-Based Control of Piezoelectric Actuators, vol. 8, pg. 181-201.

In: Serbian Journal of Electrical Engineering

  • 2011

DOI: 10.2298/SJEE1102181J

  • Elektrotechnik und Medientechnik
Beitrag (Sammelband oder Tagungsband)
  • László Juhász
  • J. Maas
Online Controller Optimization for Hybrid Micropositioning Systems, pg. 820-825.
  • 2011
  • Elektrotechnik und Medientechnik
Beitrag (Sammelband oder Tagungsband)
  • László Juhász
  • J. Maas
State-Space Control of Hybrid Micropositioning Systems for Industrial Applications, pg. 31-36.
  • 2011
  • Elektrotechnik und Medientechnik
Zeitschriftenartikel
  • László Juhász
  • J. Maas
  • B. Borovac
Parameter identifications and hysteresis compensation of embedded piezoelectric stack actuators, vol. 21, pg. 329-338.

In: Mechatronics

  • 2011

DOI: 10.1016/j.mechatronics.2010.12.006

A novel method for the identification of embedded piezoelectric stack actuator parameters in combination with a real-time capable hysteresis compensation measure is presented. The presented algorithms are based on the Maxwell resistive capacitor model and are particularly useful for the identification of piezoelectric actuators embedded in a high-precision micropositioning system where the disassembly of the complete system for separate actuator identification is not recommended or not possible. The parameter identification can be performed in a fully automated way and enables the adaptation of the compensation routine to the changed circumstances (temperature difference, wearing of actuators) as well. The hysteresis compensation method proposed here does not require significant CPU or memory resources. It can be implemented as an additional task on the already existing controller or a low-budget FPGA. As an example, the proposed method was validated experimentally by the parameter identification and hysteresis compensation of the piezoelectric actuators incorporated in a commercially available hybrid micropositioning system. The achieved experimental results are in very good agreement with the theoretical ones.
  • Elektrotechnik und Medientechnik
Beitrag (Sammelband oder Tagungsband)
  • László Juhász
  • T. Fichtner
  • A. Kiffe
  • J. Maas
Model-Based State-Space Control of Hybrid Micropositioning Systems, pg. 324-331.
  • 2010
  • Elektrotechnik und Medientechnik
Beitrag (Sammelband oder Tagungsband)
  • László Juhász
  • A. Kiffe
  • J. Maas
Friction and Hysteresis Compensation of a Hybrid Micro-Positioning System, pg. 268-271.
  • 2010
  • Elektrotechnik und Medientechnik
Beitrag (Sammelband oder Tagungsband)
  • László Juhász
  • J. Maas
  • J. Tasevski
  • B. Borovac
Multiplicative and Additive Piezoelectric Hysteresis Compensation Methods for Real-Time Micropositioning Applications
  • 2010
  • Elektrotechnik und Medientechnik
Beitrag (Sammelband oder Tagungsband)
  • László Juhász
  • A. Kiffe
  • J. Maas
  • B. Borovac
FPGA-Based Interface for Fast Data Exchange between a Rapid Control Prototyping System and a Hybrid Micropositioning Stage
  • 2009
  • Elektrotechnik und Medientechnik
Beitrag (Sammelband oder Tagungsband)
  • László Juhász
  • A. Kiffe
  • J. Maas
FPGA-Based Interface for Control of a Hybrid Micropositioning Stage, pg. 2862-2867.
  • 2009
  • Elektrotechnik und Medientechnik
Beitrag (Sammelband oder Tagungsband)
  • László Juhász
  • A. Kiffe
  • J. Maas
Modellierung und Regelung eines hybriden Nanopositionierungssystems, pg. 161-174.

In: Internationales Forum Mechatronik (ifm)

  • 2009
  • Elektrotechnik und Medientechnik
Beitrag (Sammelband oder Tagungsband)
  • László Juhász
  • F. Schütte
  • K. Diekstall
Use of rapid control prototyping (RCP) and hardware in the loop (HIL) technology for development and tests of Aerospace applications
  • 2007
  • Elektrotechnik und Medientechnik
Beitrag (Sammelband oder Tagungsband)
  • László Juhász
  • F. Schütte
  • S. Lillwitz
AFDX for Airplanes

In: Aerospace Testing International 2007

  • 2007
  • Elektrotechnik und Medientechnik
Zeitschriftenartikel
  • D. Skobalj
  • Z. Zavargó
  • László Juhász
Water temperature distribution in a vertical cross-section of a wet counterflow cooling tower, vol. 30, pg. 1-5.

In: Hungarian Journal of Industrial Chemistry

  • 2002
  • Elektrotechnik und Medientechnik
Zeitschriftenartikel
  • László Juhász
  • A. Vujanić
  • N. Adamović
  • L. Nagy
  • B. Borovac
A platform for micropositioning based on piezo legs, vol. 11, pg. 869-897.

In: Mechatronics

  • 2001

DOI: 10.1016/S0957-4158(00)00059-3

In this paper, we describe the development and prototype testing of a platform for micropositioning having three legs made of piezo tubes. Each piezo tube has four outer electrodes and one common inner electrode on its walls. By appropriate polarization of outer(s) electrode(s) with respect to the inner electrode, due to the inverse piezo effect, the tube wall will change its longitudinal dimension and the tube will bend in the corresponding direction. The platform motion is performed by successive slow bending and quick stretching of the tubes (i.e., legs). At this stage of development, the platform is connected by five wires to a power supply and a PC. The range of platform motion is limited only by the length of the wires connecting it to the power source. Electronic circuits for generating appropriate voltage signals are designed to be as simple as possible. This enabled the complete electronics and microcontroller for motion control to be placed onboard. The microcontroller is capable of realizing all operations needed for the motion execution and the communication with PC (containing the information about motion direction and step amplitude) can be done using a standard RS-232 interface. It was experimentally verified that, though being of a simple design, the platform allows a positioning accuracy which is below Full-size image (<1 K). Even more accurate positioning (below Full-size image (<1 K)) can be achieved in the “only bending” mode by simultaneous bending of all legs in a desired direction and without executing the legs' stretching. The platform capability to accomplish controlled complex motion using different motion velocities was demonstrated. Using a joystick, translation and rotation are easily achievable and the motion can be controlled in real time. Platform loading capacity allows some additional devices like a gripper, or any another device for a particular application to be mounted onboard. This enables the platform's potential use in a wide variety of applications.
  • Elektrotechnik und Medientechnik
Beitrag (Sammelband oder Tagungsband)
  • László Juhász
  • A. Vujanić
  • N. Adamović
  • L. Nagy
  • B. Borovac
Development of Platform for Micro-Positioning Actuated by Piezo-Legs, pg. 3647-3653.

In: Proceedings of the 2000 IEEE International Conference on Robotics and Automation (ICRA) [24.-28.04.2000, San Francisco, CA, USA]. null (4)

  • 2000
  • Elektrotechnik und Medientechnik
Zeitschriftenartikel
  • László Juhász
  • S. Markov
  • L. Nađ
  • B. Borovac
  • A. Vujanić
  • N. Adamović
Moving platform for sample micropositioning, vol. 54, pg. 243-257.

In: Chemical Industry

  • 2000
  • Elektrotechnik und Medientechnik
Beitrag (Sammelband oder Tagungsband)
  • László Juhász
  • T. Lozanovski
  • N. Adamović
  • A. Vujanić
  • L. Nađ
  • B. Borovac
Realisation testing of platform for micro positioning using piezo-actuators, pg. 285-288.

In: Proceedings of ETRAN '98 (01.-05.06.1998, Vrnjačka Banja, Jugoslawien). null (IV)

  • 1998
  • Elektrotechnik und Medientechnik
Beitrag (Sammelband oder Tagungsband)
  • L. Nađ
  • László Juhász
Design of CMOS buffers for driving large capacitive loads using PsPICE, pg. 35-38.

In: Proceedings of ETRAN '98 (01.-05.06.1998, Vrnjačka Banja, Jugoslawien). null (IV)

  • 1998
  • Elektrotechnik und Medientechnik
Zeitschriftenartikel
  • László Juhász
  • M. Peruničić
  • T. Kuljanin
Simulational dynamic model of a chemical reactor, vol. 52, pg. 279-285.

In: Chemical Industry (Belgrad, Serbien)

  • 1998
  • Elektrotechnik und Medientechnik
Beitrag (Sammelband oder Tagungsband)
  • László Juhász
  • A. Vujanić
  • N. Adamović
  • T. Lozanovski
  • L. Nagy
  • B. Borovac
Platform for micropositioning with piezo-actuators, pg. 103-106.
  • 1998
  • Elektrotechnik und Medientechnik
Zeitschriftenartikel
  • M. Peruničić
  • László Juhász
Contribution to analysis of proportional and proportional-integral liquid-level control in cylindrical flow tank, vol. 40

In: Documenta Chemica Yugoslavica

  • 1998
  • Elektrotechnik und Medientechnik
Beitrag (Sammelband oder Tagungsband)
  • László Juhász
  • N. Pekarić-Nađ
  • L. Nađ
EMI-oriented macromodel for operational amplifier μA741, pg. 49-52.

In: Proceedings of ETRAN '98 (01.-05.06.1998, Vrnjačka Banja, Jugoslawien). null (IV)

  • 1998
  • Elektrotechnik und Medientechnik
Beitrag (Sammelband oder Tagungsband)
  • László Juhász
  • Đ. Garabandić
  • M. Živanov
Digital regulation of the BUCK DC/DC converter, pg. 513-521.
  • 1997
  • Elektrotechnik und Medientechnik
Beitrag (Sammelband oder Tagungsband)
  • László Juhász
  • Đ. Garabandić
  • M. Živanov
BUCK DC/DC converter controlled by microcontroller, pg. 135-140.
  • 1997
  • Elektrotechnik und Medientechnik
Zeitschriftenartikel
  • M. Peruničić
  • László Juhász
Dynamics of a spherical gravity flow tank, vol. 39, pg. 85-88.

In: Documenta Chemica Yugoslavica

  • 1997
  • Elektrotechnik und Medientechnik
Zeitschriftenartikel
  • M. Peruničić
  • László Juhász
  • A. Sadibašić
The dynamics of a conical gravity flow tank, vol. 51, pg. 24-27.

In: Chemical Industry (Belgrad, Serbien)

  • 1997
  • Elektrotechnik und Medientechnik
Beitrag (Sammelband oder Tagungsband)
  • Đ. Garabandić
  • T. Petrović
  • László Juhász
Robust decentralised control of parallel DC/DC converters, pg. 563-570.
  • 1995
  • Elektrotechnik und Medientechnik

other

A video about a student's project conducted in the lab Model-Based Control-Design and Test

https://nextcloud.th-deg.de/s/F5jnrG2B2YzHL64